Avaya J100 Series Installing And Administering Download Page 309

Page: 309 / 528

Parameter name

Default value

Description

BLF_PARKED_CALL_INDICATION_MODE

Specifies the indication
move for a BLF parked
call.

Valid values:

• 0 - None (no alerting for

BLF parked call).

• 1 - Audible (only audible

alerting for BLF parked
call).

• 2 - Visual (only visual

alerting for BLF parked
call).

• 3 - Both (both audible

and visual alerting for
BLF parked call)

• 4 - Force None (forced

only audible alerting for
BLF parked call).

• 5 - Force Audible (forced

only audible alerting for
BLF parked call).

• 6 - Force Visual (forced

only visual alerting for
BLF parked call).

• 7 - Force Both (forced

both audible and visual
alerting for BLF parked
call).

Note:

This parameter is
supported only in the
3PCC environment.

Table continues…

List of configuration parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

309

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Search results

Summary of Contents for J100 Series

Reviews:

Avaya J100 Series, Installing And Administering, Page: 309 / 528

Search results

Summary of Contents for J100 Series

Reviews: