Avaya J100 Series Installing And Administering Download Page 428

Page: 428 / 528

Parameter name

Default value

Description

REUSETIME

Specifies the number of
seconds that the DHCP is
attempted:

• With a VLAN ID of zero.

True when L2Q is set to
1.

• With untagged frames.

True if L2Q is set to 0 or
2.

• Before reusing the IP

address and the
associated address
information, that the
phone had the last time
it successfully registered
with a call server.

While reusing an address,
DHCP enters the
extended rebinding state
described above for
DHCPSTD.

Valid values are 0 and 20
through 999. The default
value is 60. A value of
zero means that DHCP
will try forever and there
will be no reuse.

Table continues…

Customizable parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

428

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Search results

Summary of Contents for J100 Series

Reviews:

Avaya J100 Series, Installing And Administering, Page: 428 / 528

Search results

Summary of Contents for J100 Series

Reviews: