manualshive.com logo in svg

Avaya J100 Series, Installing And Administering, Page: 371 / 528

Share
Download
Avaya J100 Series Installing And Administering Download Page 371

Parameter name

Default value

Description

HANDSET_PROFILE_NAMES

Null

Specifies an ordered list of
names to be displayed for
handset audio profile
selection. The list can
contain 0 to 255 UTF-8
characters.

Names are separated by
commas without any
intervening spaces. Two
commas in succession
indicate a null name,
which means that the
default name should be
displayed for the
corresponding profile.
Names might contain
spaces, but if any do, the
entire list must be quoted.
There is no way to prevent
a profile from being
displayed.

HEADSET_PROFILE_DEFAULT

1

Specifies the number of
the default headset audio
profile.

Valid values are 1 through
20.

Note:

Avaya J129 IP
Phonedoes not
support this feature.

Table continues…

List of configuration parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

371

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Reviews:

No comments