manualshive.com logo in svg

Avaya J100 Series, Installing And Administering, Page: 385 / 528

Share
Download
Avaya J100 Series Installing And Administering Download Page 385

Parameter name

Default value

Description

LOG_DIALED_DIGITS

1

Specifies if the call log will
contain digits dialed by a
user or information about
a remote party when the
user dials a FAC code.

The FAC code is identified
by * or # entered as a first
character.

Value operation:

• 0: Allow dialed FAC

code to be replaced with
a remote party number
in the call history

• 1: Dialed digits are

logged in call history
exactly as they were
entered by the user
(default).

LOGSRVR

Null

Specifies one address for
a syslog server in dotted-
decimal formatl (IPv4),
colon-hex format (IPv6, if
supported), or DNS name
format.

The value can contain 0 to
255 characters.

M

Table continues…

List of configuration parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

385

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Reviews:

No comments