manualshive.com logo in svg

Avaya J100 Series, Installing And Administering, Page: 54 / 528

Share
Download
Avaya J100 Series Installing And Administering Download Page 54

Option

Description

Option 55

Specifies the parameter request list. Acceptable values are:

• 1 for subnet mask

• 3 for router IP addresses

• 6 for domain name server IP addresses

• 7 for log server

• 15 for domain name

• 42 for NTP servers

Option 57

Specifies the maximum DHCP message size.

Set the value to 1500.

Set the value to 1000.

Option 58

Specifies the DHCP lease renew time. If not received or if this value is greater than
that for Option 51, the default value of T1, renewal timer is used.

Option 59

Specifies the DHCP lease rebind time. If not received or if this value is greater than
that for Option 51, the default value of T2, rebinding timer is used.

Option 242

Specifies the site-specific option (SSON). It is optional but cannot be used
simultaneously with Option 43.

If you do not configure this option, ensure that one of the following parameters is
configured appropriately elsewhere:

• HTTPSRVR

• TLSSRVR

DHCP vendor-specific option

You can set DHCP vendor-specific parameters by using DHCP option 43. The supported codes for

Option 43 and the corresponding parameters are as follows:

Code

Parameter

1

Does not set any parameter. The value must be 6889.

2

HTTPSRVR

3

HTTPDIR

4

HTTPPORT

5

TLSSRVR

6

TLSDIR

7

TLSPORT

8

TLSSRVRID

9

L2Q

10

L2QVLAN

Table continues…

Servers, VLAN, and IP configuration

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

54

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Reviews:

No comments