manualshive.com logo in svg

Avaya J100 Series, Installing And Administering, Page: 296 / 528

Share
Download
Avaya J100 Series Installing And Administering Download Page 296

Parameter name

Default value

Description

APPLICATION_HEADER_APPEARANCE_CONTEXT

0

Specifies whether
appearances context will
be shown on the
Application Header Line in
Phone List View. This
Application Header
context relies on
SHORT_FORM_USER_ID
and DISPLAY_NAME to
display the Application
Header line context
appropriately.

Value operation:

0 - appearances context
will not be shown on the
Application Header Line
(default)

1 - appearances context
will be shown on the
Application Header Line

If this parameter is
enabled but both
SHORT_FORM_USER_ID
and DISPLAY_NAME are
null, then the userid of the
registered SIP user will be
displayed.

Note:

Avaya J129 IP
Phonedoes not
support this
parameter.

Table continues…

Customizable parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

296

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Reviews:

No comments