manualshive.com logo in svg

Avaya J100 Series, Installing And Administering, Page: 465 / 528

Share
Download
Avaya J100 Series Installing And Administering Download Page 465

Parameter name

Default value

Description

SYMMETRIC_RTP

1

Specifies if the phone
must discard received
RTP datagrams if their
UDP source port number
is not the same as the
UDP destination port
number included in the
RTP datagrams of that
endpoint.

Value operation:

0: Ignore the UDP source
port number in received
RTP datagrams.

1: Discard received RTP
datagrams (default).

SYSLOG_ENABLED

0

Specifies if Syslog
messages must be send
or not.

Value operation:

0: Sending Syslog
messages is disabled
(default)

1: Sending Syslog
messages is enabled

Table continues…

List of configuration parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

465

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Reviews:

No comments