manualshive.com logo in svg

Avaya J100 Series, Installing And Administering, Page: 310 / 528

Share
Download
Avaya J100 Series Installing And Administering Download Page 310

Parameter name

Default value

Description

BLF_PICKUP_METHOD

0

Specifies whether pickup
BLF call is using Invite
with FAC in Request URI
or using Invite with
Replaces header.

Value operation:

• 0: Pickup BLF call using

Invite with FAC in
Request URI

• 1: Pickup BLF call using

Invite with Replaces
header

Note:

This parameter is
available in

• Avaya J139 IP

Phone

• Avaya J159 IP

Phone

• Avaya J169/J179

IP Phone

BLOCK_CERTIFICATE_WILDCARDS

0

Specifies whether the
endpoint will accept server
identity certificates with
wildcards.

Value operation:

• 0: Accept wildcards in

certificate.

• 1: Do not accept

wildcards in certificates.

Table continues…

Customizable parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

310

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Reviews:

No comments