manualshive.com logo in svg

Avaya J100 Series, Installing And Administering, Page: 337 / 528

Share
Download
Avaya J100 Series Installing And Administering Download Page 337

Parameter name

Default value

Description

DIRAUTHTYPE

1

Specifies the kind of
authentication that is used
if the value of the
DIRUSERNAME
parameter is not null.

Value operation:

• 0: Simple LDAP

authentication. Normally
the DIRUSERNAME
parameter must contain
a DN name of an LDAP
record, and
DIRUSERNAME must
contain a password
associated with the
record.

• 1: Simple LDAP

Authentication and
Security Layer (SASL).

If a connection is
established over TLS
(DIRSECURE is set to 1
or 2), DIGEST-MD5 or
PLAIN authentication
mechanisms are
supported.

If the connection
established over TCP
(DIRSECURE is set to
0) DIGEST-MD5 is the
only supported
mechanism.

Note:

Avaya J129 IP Phone
does not support this
parameter.

Table continues…

List of configuration parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

337

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Reviews:

No comments