Avaya J100 Series Installing And Administering Download Page 300

Page: 300 / 528

Parameter name

Default value

Description

AUTHCTRLSTAT

Specifies that the
enhanced debugging
capabilities are activated
from an SSH server by an
AVAYA engineer.

Value operation:

• 0: Enhanced debugging

capabilities are disabled.

• 1: Enhanced debugging

capabilities are enabled.

Note:

The parameter must
be set to 1 only for
the debugging period.
Set the parameter
back to 0 when
debugging is
complete.

AUTO_ANSWER_DURING_CALL

Specifies auto-answer
calls during another active
call.

Value operation:

• 0: Do not auto-answer

when there is an active
call

• 1: Auto-answer when

there is an active call

Note:

Avaya J129 IP Phone
does not supports
this feature.

AUTO_ANSWER_MUTE_ENABLE

Specifies the status of the
mute function for the auto-
answered calls.

Value operation:

• 0: Disabled

• 1: Enabled

Table continues…

Customizable parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

300

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Search results

Summary of Contents for J100 Series

Reviews:

Avaya J100 Series, Installing And Administering, Page: 300 / 528

Search results

Summary of Contents for J100 Series

Reviews: