manualshive.com logo in svg

Avaya J100 Series, Installing And Administering, Page: 429 / 528

Share
Download
Avaya J100 Series Installing And Administering Download Page 429

Parameter name

Default value

Description

RINGTONE_ALERTINFO

Null

Specifies a comma
separated list of specific
ring tones assigned to a
call queue
(QueueID:SelectedRingto
neID).

QueueID is a string
matching the call queue
name, as configured in the
3CX server.

SelectedRingtoneID is a
numerical index of one of
the ringtones known to the
phone.

When the 3CX server is
not configured for distinct
ringtones per queue, the
only supported QueueID is
"queue".

Note:

The parameter is
supported in OpenSIP
environment only and
when
3PCC_SERVER_MODE is
set to 2 (3CX).

RINGTONE_DEFAULT_ALTERNATE_NUM2

17

Specifies the index of the
default ringtone to be used
when an incoming call is
from the second alternate
number. Specifies the
index of the default
ringtone to be used when
an incoming call is from
the second alternate
number.

Note:

This parameter is
applicable only for
Broadsoft
environment.

Table continues…

List of configuration parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

429

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Reviews:

No comments