Avaya J100 Series Installing And Administering Download Page 384

Page: 384 / 528

Parameter name

Default value

Description

Warning:

Setting the value to 7
can impact the
performance of the
phone because of the
number of events
generated.

LOG_CATEGORY

Null

Specifies a list of
categories of events to be
logged through syslog and
locally.

This parameter must be
specified to log events
below the Error level.

The list can contain up to
255 characters.

Category names are
separated by commas
without any intervening
spaces.

H1xx SIP R1.0 and later;
the default is ALL which
implies all categories.

New categories for H1xx
compare to 96x1 SIP
include ANDROID and
KERNEL.

Table continues…

Customizable parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

384

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Search results

Summary of Contents for J100 Series

Reviews:

Avaya J100 Series, Installing And Administering, Page: 384 / 528

Search results

Summary of Contents for J100 Series

Reviews: