Avaya J100 Series Installing And Administering Download Page 299

Page: 299 / 528

Parameter name

Default value

Description

AUDIOSTHS

Specifies the level of side-
tone in the handset.

Value operation:

• 0: Normal

• 1: Softer by three levels.

• 2: OFF.

• 3: Softer by one level.

• 4: Softer by two levels.

• 5: Softer by four levels.

• 6: Softer by five levels.

• 7: Softer by six levels.

• 8: Louder by one level.

• 9: Louder by two levels.

Note:

Avaya J159 IP Phone
and Avaya J169/J179
IP Phone supports
this feature.

AUTH

Specifies if the script files
are to be downloaded from
an authenticated server
over an HTTPS link.

Value operation:

• 0: Optional

• 1: Mandatory

To revert the configured
value of 1 to the default
one, reset the phone to
defaults.

Table continues…

List of configuration parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

299

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Search results

Summary of Contents for J100 Series

Reviews:

Avaya J100 Series, Installing And Administering, Page: 299 / 528

Search results

Summary of Contents for J100 Series

Reviews: