Avaya J100 Series Installing And Administering Download Page 481

Page: 481 / 528

Parameter name

Default value

Description

WMLHOME

Null

Specifies the URL of a
WML page to be displayed
by default in the WML
browser and if the

Home

soft key is selected in the
browser.

The allowed value
contains not more than
one URL of up to 255
characters.

Note:

If the value is set to
default, the WML browser
is disabled.

Only Avaya J169/J179 IP
Phones support this
parameter.

WMLIDLETIME

Specifies the idle time in
minutes after which the
web page set as the value
of WMLIDLEURI will be
displayed.

The allowed value is a
positive integer from 1 to
999.

Note:

If WMLIDLEURI is
set to null, the web
page will not be
displayed when the
phone is idle.

Only Avaya J169/J179 IP
Phones support this
parameter.

Table continues…

List of configuration parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

481

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Search results

Summary of Contents for J100 Series

Reviews:

Avaya J100 Series, Installing And Administering, Page: 481 / 528

Search results

Summary of Contents for J100 Series

Reviews: