Avaya J100 Series Installing And Administering Download Page 103

Page: 103 / 528

4. Click one of the following:

•

Save

: To save the configuration changes.

•

Reset to Default

: To revert to the default values.

Network settings field description

Name

Description

Network

Network Mode of Operation

Specifies the network mode used by the phone.

The operations are:

•

Ethernet only

•

Ethernet (preferred, but manual override
allowed from Phone UI) (default)

•

Wi-Fi (preferred, but manual override allowed
from Phone UI)

DNS

DNS Server

Specifies the IP addresses of the DNS servers
added to the network.

Valid value is IP addresses in dotted-decimal
format, separated by commas without any
intervening spaces.

The default value is empty.

Note:

You can add up to 16 DNS servers.

DNS Domain

Specifies the domain name of the DNS server.

Valid value must be in the DNS name format. The
default value is empty.

ICMP

Destination Unreachable Message Control

Specifies the type of the ICMP destination
unreachable messages.

The options are:

•

Limited Port Unreachable messages (default)

•

Protocol and Port Unreachable messages

Table continues…

Configuring the phone using the web interface

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

103

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Search results

Summary of Contents for J100 Series

Reviews:

Avaya J100 Series, Installing And Administering, Page: 103 / 528

Search results

Summary of Contents for J100 Series

Reviews: