manualshive.com logo in svg

Avaya J100 Series, Installing And Administering, Page: 439 / 528

Share
Download
Avaya J100 Series Installing And Administering Download Page 439

Parameter name

Default value

Description

SCA<n>_PASSWORD

Null

Specifies the password
used for authentication
when challenged with 401
for credentials on SIP
requests associated with
the shared line. <n> can
be a number of 1 to 8.
This is a required
parameter in SCA mode.

The Ring Central Server
ignores this value and
uses authentication
credentials provided in
SCA<n>_SIPUSERID.

Note:

These parameters
are supported only by
Avaya J139 IP
Phone, Avaya J159
IP Phone and Avaya
J169/J179 IP Phone.

SCA<n>_SIPUSERID

Null

Specifies the Address or
Record (AOR) for each
shared line. This
parameter is required for
both the SCA and BLA
modes. <n> can be a
number of 1 to 8.

This parameter should
only specify the handle, as
the domain is specified
independently.

Shared lines are only
supported for the same
SIP domain as the primary
line.

Note:

These parameters
are supported only by
Avaya J139 IP
Phone, Avaya J159
IP Phone and Avaya
J169/J179 IP Phone.

Table continues…

List of configuration parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

439

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Reviews:

No comments