Avaya J100 Series Installing And Administering Download Page 292

Page: 292 / 528

Appendix A: Customizable parameters

List of configuration parameters

Parameter name

Default value

Description

100REL_SUPPORT

Specifies whether the
100rel option tag is
included in the

SIP INVITE

header field.

Value operation:

• 0: Not included.

• 1: Included.

3PCC_SERVER_MODE

Specifies the server mode.

Value operation:

• 0: Generic

• 1: BroadSoft

• 2: 3CX

• 3: Netsapiens

• 4: RCO , Avaya J129 IP

Phone does not support
this value.

• 5: ACO, Avaya J129 IP

Phone does not support
this value.

Table continues…

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

292

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Search results

Summary of Contents for J100 Series

Reviews:

Avaya J100 Series, Installing And Administering, Page: 292 / 528

Search results

Summary of Contents for J100 Series

Reviews: