manualshive.com logo in svg

Avaya J100 Series, Installing And Administering, Page: 349 / 528

Share
Download
Avaya J100 Series Installing And Administering Download Page 349

Parameter name

Default value

Description

DTMF_PAYLOAD_TYPE

120

Specifies the RTP payload
type to be used for RFC
2833 signaling.

Valid values are 96
through 127.

E
EASG_SITE_AUTH_FACTOR

Null

Specifies Site
Authentication Factor code
associated with the EASG
site certificate being
installed. Valid values are
10 to 20 character
alphanumeric string.

EASG_SITE_CERTS

Null

Specifies list of EASG site
certificates which are used
by technicians when they
don't have access to the
Avaya network to generate
EASG responses for SSH
login. The URLs must be
separated by commas
without any intervening
spaces. Valid values are 0
to 255 ASCII characters.

EEESTAT

1

Specifies Energy-Efficient
Ethernet (802.3az) is
enabled on PHY1 and
PHY2.

Value operation:

• 0: EEE is disabled on

both PHY1 and PHY2.

• 1: EEE is enabled on

both PHY1 and PHY2.

This parameter is
supported by only Avaya
J129 IP Phone.

Table continues…

List of configuration parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

349

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Reviews:

No comments