Avaya J100 Series Installing And Administering Download Page 425

Page: 425 / 528

Parameter name

Default value

Description

RECORDINGTONE_VOLUME

Specifies the volume of
the call recording tone in
5dB steps.

Value operation:

• 0: The tone volume is

equal to the transmit
audio level (default).

• 1: The tone volume is

45dB below the transmit
audio level.

• 2: The tone volume is

40dB below the transmit
audio level.

• 3: The tone volume is

35dB below the transmit
audio level.

• 4: The tone volume is

30dB below the transmit
audio level.

• 5: The tone volume is

25dB below the transmit
audio level.

• 6: The tone volume is

20dB below the transmit
audio level.

• 7: The tone volume is

15dB below the transmit
audio level.

• 8: The tone volume is

10dB below the transmit
audio level.

• 9: The tone volume is

5dB below the transmit
audio level.

• 10: The tone volume is

equal to the transmit
audio level.

Note:

Avaya J129 IP Phone
does not support this
parameter.

Table continues…

List of configuration parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

425

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Search results

Summary of Contents for J100 Series

Reviews:

Avaya J100 Series, Installing And Administering, Page: 425 / 528

Search results

Summary of Contents for J100 Series

Reviews: