manualshive.com logo in svg

Avaya J100 Series, Installing And Administering, Page: 363 / 528

Share
Download
Avaya J100 Series Installing And Administering Download Page 363

Parameter name

Default value

Description

ENCRYPT_SRTCP

0

Specifies whether the
encrypted SRTCP is
supported.

Value operation:

• 0: Not supported.

• 1: Supported.

ENFORCE_SIPS_URI

1

Specifies if a SIPS URI
must be used for SRTP.

Value operation:

• 0: Not enforced

• 1: Enforced

Note:

For 3PCC
environments using
TLS signaling, must
be set to 0.

ENHDIALSTAT

1

Specifies if the algorithm
defined by the parameter
is used during certain
dialing behaviors.

Value operation:

• 0: Disables algorithm.

• 1: Enables algorithm, but

not for Contacts.

• 2: Enables algorithm,

including Contacts.

• 3: Unconditionally apply

enhanced dialing rules.

Table continues…

List of configuration parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

363

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Reviews:

No comments