Avaya J100 Series Installing And Administering Download Page 460

Page: 460 / 528

Parameter name

Default value

Description

SOFTKEY_CONFIGURATION

0,1,2

Specifies which feature
will show up on which soft
key on the Avaya J129 IP
Phone screens.

The features are defined
as follows:

• 0 = Redial

• 1 = Contacts

• 2 = Emergency

• 3 = Recents

• 4 = Voicemail

Note:

Emergency calls are
not supported in an
Open SIP
environment.

SPEAKERSTAT

Specifies the operation of
the speakerphone.

Value operation:

0: Speakerphone disabled

1: One-way speaker (also
called monitor) enabled.

2: Full (two-way)
speakerphone enabled.

Note:

Avaya J129 IP Phone
does not support this
feature.

SSH_ALLOWED

Specifies if SSH is
supported.

Value operation:

0: Disabled

1: Enabled

2: Configured using local
craft procedure. When this
mode is configured, then
by default the SSH server
is disabled.

Table continues…

Customizable parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

460

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Search results

Summary of Contents for J100 Series

Reviews:

Avaya J100 Series, Installing And Administering, Page: 460 / 528

Search results

Summary of Contents for J100 Series

Reviews: