Avaya J100 Series Installing And Administering Download Page 381

Page: 381 / 528

Parameter name

Default value

Description

L2QVLAN

Specifies the voice VLAN
ID to be used by IP
phones.

Valid values are 0 through
4,094.

Note:

This parameter can
also be set through:

• Local admin

procedure

• A name equal to

value pair in
DHCPACK
message

• SET command in

the settings file

• DHCP option 43

• LLDP

LANGLARGEFONT

Null

Specifies the name of the
language file for the
display of large text.

The file name can contain
0 to 32 ASCII characters.
When you set the
parameter to the default
value null, the

Text Size

option is not available.

Note:

Avaya J169/J179 IP
Phone supports this
parameter.

LANGUAGES

Null

Specifies the language
files that must installed or
downloaded to the phone.

Filenames can be full
URL, relative pathname,
or filename comma
separated filenames
ending with

.xml

Table continues…

List of configuration parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

381

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Search results

Summary of Contents for J100 Series

Reviews:

Avaya J100 Series, Installing And Administering, Page: 381 / 528

Search results

Summary of Contents for J100 Series

Reviews: