Avaya J100 Series Installing And Administering Download Page 347

Page: 347 / 528

Parameter name

Default value

Description

DOT1XSTAT

Specifies the 802.1X
supplicant operating
mode.

Value operation:

0: Supplicant disabled

1: Supplicant enabled, but
responds only to received
unicast EAPOL messages

2: Supplicant enabled;
responds to received
unicast and multicast
EAPOL messages

DSCPAUD

Specifies the layer 3
Differentiated Services
(DiffServ) Code Point for
audio frames generated by
the phone.

Valid values are from 0 to
63.

This parameter can also
be set through the LLDP,
which overwrites any
value in the settings file.

DSCPAUD_FL

Specifies the DSCP value
for flash precedence or
priority level voice call.

Valid values are from 0 to
63.

DSCPSIG

Specifies the layer 3
Differentiated Services
(DiffServ) Code Point for
signaling frames
generated by the phone.

Valid values are 0 through
63.

This parameter can also
be set through LLDP,
which overwrites any
value set in the settings
file.

Table continues…

List of configuration parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

347

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Search results

Summary of Contents for J100 Series

Reviews:

Avaya J100 Series, Installing And Administering, Page: 347 / 528

Search results

Summary of Contents for J100 Series

Reviews: