Avaya J100 Series Installing And Administering Download Page 311

Page: 311 / 528

Parameter name

Default value

Description

BRANDING_VOLUME

Specifies the volume level
at which the Avaya audio
brand is played.

Value operation:

• 8: 9db above nominal

• 7: 6db above nominal

• 6: 3db above nominal

• 5: nominal (default)

• 4: 3db below nominal

• 3: 6db below nominal

• 2: 9db below nominal

• 1: db below nominal

BRURI

Null

Provides the capability to
send a phone report to a
server with the URI of the
server defined by this
parameter. To send the
report, go to

Main Menu

Admin

Debug

Phone

report

BS_CC_ENABLED

Specifies if the Broadsoft
Call Center needs to be
enabled on the phone.
This parameter is used
only if XSI is disabled
(XSI_URL is empty).

Options are:

• 0: To disable the

parameter.

• 1: To enable the

parameter.

Note:

Avaya J129 IP Phone
does not support this
feature.

Table continues…

List of configuration parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

311

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Search results

Summary of Contents for J100 Series

Reviews:

Avaya J100 Series, Installing And Administering, Page: 311 / 528

Search results

Summary of Contents for J100 Series

Reviews: