manualshive.com logo in svg

Avaya J100 Series, Installing And Administering, Page: 458 / 528

Share
Download
Avaya J100 Series Installing And Administering Download Page 458

Parameter name

Default value

Description

SNTP_SYNC_INTERVAL

1440 minutes

Specifies the time interval,
in minutes, during which
the phone attempts to
synchronize its time with
configured NTP servers.
Valid values are from 60 to
2,880 minutes.

SNTPSRVR

Null

Specifies a list of
addresses of SNTP
servers.

Addresses can be in
dotted-decimal or DNS
name format, separated
by commas without any
intervening spaces.

The list can contain up to
255 characters.

Table continues…

Customizable parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

458

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Reviews:

No comments