manualshive.com logo in svg

Avaya J100 Series, Installing And Administering, Page: 410 / 528

Share
Download
Avaya J100 Series Installing And Administering Download Page 410

Parameter name

Default value

Description

PNP_ENABLED

1

Specifies if PnP is enabled
or not. This value does not
define if it is to be
activated or not but only
defines if PnP can be
activated. Typically this is
used only to block PnP
from occurring on new and
reset to default phones.

Value operation:

• 0: PNP is blocked

(default).

• 1: PNP is allowed.

PRESERVE_MEDIA_CONNECTIONS

0

Specifies whether to
preserver media
connections for the
servers that do not comply
with 

RFC 3264 8.2

.

Value operation:

• 0: Do not preserve

media connections.

• 1: Preserver media

connections.

PRESERVED_CALL_DURATION

120

Specifies the time interval
in minutes if
ENABLE_IPOFFICE is set
to 2 and if
MEDIA_PRESERVATION
is set to 1.

The time interval can be
from 10 minutes to 120
minutes.

Table continues…

Customizable parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

410

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Reviews:

No comments