Home
/
Avaya
/
J100 Series
/
Installing And Administering

Avaya J100 Series, Installing And Administering, Page: 212 / 528

Share

Page: 212 / 528

Avaya J100 Series Installing And Administering Download Page 212

Parameter name

Default value

Description

BS_CC_DISP_CODES

Null

Specifies call dispositions codes
that the call center agents can
apply to a call center call. You can
enter comma separated string
values of disposition codes.
Disposition code does not support
special characters.

For example: 1=Follow-up
required, sales:2=New customer,
helpdesk:3=Issue resolved;
4=Issue unresolved.

Here, 1 is available for all call
centers, 2 is specific for sales,
and 3, and 4 are specific for
helpdesk.

Use this parameter only if XSI is
disabled (XSI_URL is empty).

Note:

This parameter is available
in:

• Avaya J159 IP Phone

• Avaya J169/J179 IP Phone

Table continues…

Feature and application configuration

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

212

Comments on this document? [email protected]

«
...
210
211
212
213
214
...
»

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Reviews:

No comments