Altigen AltiContact Manager Version 5.0 Administration Manual Download | Manualshive

Page: 145 / 542

background image

Getting Around ACM Administrator

AltiContact Manager Administration Manual

4-7

4

.

G

e

tting

Ar
ound

ACM

Admin

Trunk View Window

The Trunk View window displays the status of all assigned trunks.

Figure 5.

Trunk View window

The radio button to the left of each trunk location is green when the trunk
is idle, and red when the extension is not ready or in use. The location
format is slot:channel—for example, channel 3 on the board in slot 9 is
location 09:03.

You can double click any trunk location to open the Trunk Configuration
window for the selected trunk.

The Reset button resets the selected trunk(s) to the idle status. You’ll be
asked to confirm the reset and a status message will tell you if the reset was
successful. You can select and reset multiple trunks.

«
...
143
144
145
146
147
...
»

Summary of Contents for AltiContact Manager Version 5.0































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AltiContact Manager Version 5.0

Brand: F-SECURE Pages: 43

Brand: Canon Pages: 2

DL385 - ProLiant - G5

Brand: XenSource Pages: 313

E-20 - Dual Monaural Earphones

Brand: Olympus Pages: 2

3C19250 - USB Ethernet Network Interface...

Brand: 3Com Pages: 16

Brand: Novell Pages: 126

PROLIANT 56976839

Brand: HP Pages: 16

ProLiant Power Interface Control Utility

Brand: HP Pages: 10

Brand: HP Pages: 181

ProLiant SL160s

Brand: HP Pages: 8

Brand: HP Pages: 245

ProBook 6445b - Notebook PC

Brand: HP Pages: 183

ProLiant Lights Out-100

Brand: HP Pages: 60

StorageWorks 2/64 - Core Switch

Brand: HP Pages: 830

StorageWorks 2/64 - Core Switch

Brand: HP Pages: 166

Brand: HP Pages: 157

ProBook 6445b - Notebook PC

Brand: HP Pages: 230

DESKTOP VERSION 1.2

Brand: Livescribe Pages: 70

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands