manualshive.com logo in svg

Altigen AltiContact Manager Version 5.0, Administration Manual

Share
Download
Altigen AltiContact Manager Version 5.0 Administration Manual Download Page 66

Key AltiContact Manager Characteristics

1-28

AltiContact Manager Administration Manual

• Automatic Call Distribution

• IVR

• System Call Back

• Calling Out from Voice Mail

• Zoomerang

• Dial Last Caller

• Speed Dialing

• Call Accounting

• Caller ID

• Voice Mail

• MS Exchange Integration

• AltiConsole Client Support

• AltiReach Support

• AltiView/AltiView IP Extensions

• Intercom

• IP Extension Log In/Log Out

• Conversation recording

• Trunk recording

AltiWare Tools

AltiWare comes with useful tools for testing, diagnosing and operating
your AltiContact Manager configuration.

•

AltiVR Player - voice recording playback tool that can be used by the
administrator to access all voice recording data in a centralized
location.

•

CT-bus Test Tool - detects one-way connection, cross talk, bad MVIP
cable, and static noise problems.

•

DINA Manager - an application that allows a system administrator to
configure several distributed systems from a single system. The tool
can be run on any server (local or remote) to an AltiContact Manager
system that has a connection for access to all the servers to be
managed. DINA Manager can support multiple versions of AltiWare
and AltiContact Manager. Also, extensions across multiple systems
can be deleted. In ACM 5.0, the following enhancement has been
made:

Summary of Contents for AltiContact Manager Version 5.0































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands