Altigen AltiContact Manager Version 5.0 Administration Manual Download

Page: 306 / 542

Call Recording

12-10

AltiContact Manager Administration Manual

This invokes the Add Network Place Wizard. Click Next.

Figure 7.

Add Network Place Wizard

Click Next.

Figure 8.

Add Network Place Wizard

Type the address of the Internet or network address (UNC format -
\\server-name\shared-resource-pathname) in the field, for

Summary of Contents for AltiContact Manager Version 5.0































































































































































































































































































































































































































































































































































Search results

Summary of Contents for AltiContact Manager Version 5.0

Reviews:

Related manuals for AltiContact Manager Version 5.0

Brands by name

Popular brands

Altigen AltiContact Manager Version 5.0, Administration Manual

Search results

Summary of Contents for AltiContact Manager Version 5.0

Reviews:

Related manuals for AltiContact Manager Version 5.0

Brands by name

Popular brands