manualshive.com logo in svg

Altigen AltiContact Manager Version 5.0, Administration Manual

Share
Download
Altigen AltiContact Manager Version 5.0 Administration Manual Download Page 200

Configuring the Triton T1/E1/PRI Board

6-18

AltiContact Manager Administration Manual

File Name. The Operating mode is automatically displayed as T1/
PRI or E1/PRI.

•

The Span Info window displays the Total Number of Spans on the
board and the status of the span in the Span Info window. To reset the
span, click the Reset Span button. Double clicking a span in this
window will invoke a configuration window, as discussed in the
following section.

See “T1 Clocking” on page 6-24 and the Status Messages table beginning
in the next section.

Triton T1 Configuration - Triton T1/PRI/E1 Dialog Box

Double clicking the span line for a Triton T1 board in the Span Info
window invokes a T1/PRI or E1/PRI Configuration dialog box.

Figure 10.

Triton T1/PRI Configuration dialog box

Summary of Contents for AltiContact Manager Version 5.0































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands