Altigen AltiContact Manager Version 5.0 Administration Manual Download | Manualshive

Page: 72 / 542

background image

2-2

AltiContact Manager Administration Manual

— Windows 2000 Professional with SP4 and above (SmallOffice and

AltiServ1 IP only)

— Windows Server 2003

Note:

If installing AltiContact Manager for the first time and you
wish to use the software with Windows 2000, you must already
be running Windows 2000 prior to the AltiContact Manager
software installation.

Note:

If migrating to AltiContact Manager, migration from AltiServ
is available.

• For 5.0 Administrator:

— Windows 2000 Server/Professional with SP4 and above

— Windows Server 2003

— Windows XP Professional

• For 5.0 Client Applications:

— Windows 98 2nd Edition

— Windows 2000 Server/Professional with SP4 and above

— Windows XP Professional

• For Online Help: Internet Explorer 6.0 or higher browser.

To accommodate Quantum and Triton telephony boards with AltiContact
Manager software, ACM requires the following minimum system
configuration:

• IBM/PC compatible system with adequate number of full-size ISA and

PCI slots.

• Microsoft Windows 2000 Server.

• Microsoft Internet Information Services (version 3 or higher for

Windows 2000 [web server software that is supplied with Windows])
must be installed prior to installing AltiContact Manager. This is
necessary if you want AltiReach, the web-based call handling
application, to run.

• Channel Service Unit for T1/E1/PRI.

Hardware selection may have to be adjusted based on the following
variables:

• The number of AltiGen telephony boards required

«
...
70
71
72
73
74
...
»

Summary of Contents for AltiContact Manager Version 5.0































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AltiContact Manager Version 5.0

Brand: F-SECURE Pages: 18

Brand: Oberheim Pages: 64

FLEX - DEVELOPING COMPONENTS AND THEMES

Brand: MACROMEDIA Pages: 82

DRAGON NATURALLYSPEAKING PROFESSIONAL 5

Brand: Dragon Systems Pages: 222

Brand: Allied Telesis Pages: 46

POLICY MANAGER 7.0 -

Brand: F-SECURE Pages: 241

Sun GlassFish EnterpriseServer v3 Prelude

Brand: Sun Microsystems Pages: 48

Sun StorEdge Availability Suite 3.2

Brand: Sun Microsystems Pages: 52

Brand: VDO Pages: 8

DuraStor 6220SS

Brand: Adaptec Pages: 133

Brand: Adaptec Pages: 174

3C16120 - SuperStack 3 Server Load Balancer

Brand: 3Com Pages: 99

Brand: Intel Pages: 43

Brand: TomTom Pages: 58

3C15500 - Network Director - PC

Brand: 3Com Pages: 924

Brand: McAfee Pages: 315

MOVI 4.0 - FOR MAC

Brand: TANDBERG Pages: 19

Brand: Quantum Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands