Altigen AltiContact Manager Version 5.0 Administration Manual Download | Manualshive

Page: 194 / 542

background image

Configuring the Triton T1/E1/PRI Board

6-12

AltiContact Manager Administration Manual

Service Parameters for T1

To subscribe to T1 service, certain parameters are required to establish
service. The information provided below identifies the recommended and
supported parameters for T1 service.

T1 Service Request Information

When ordering T1 service, provide the following service request
information:

Equipment Information

Product Manufacturer - AltiGen Communications, Inc.

Product Name - AltiContact Manager Phone System

CSU/DSU - ADTRAN T1 ACE (recommended) or other CSU/DSU

Technical Information for T1 with Voice

Signaling Protocol:

• E&M Wink Start (recommended)

• E&M Immediate Start

• Ground Start

• Loop Start (not recommended)

Trunk Type:

• DID

• 2-Way DID (recommended)

• DOD

Framing:

• Super Frame (SF)/D4

• Extended Super Frame (ESF) (recommended)

Line Coding:

• Alternate Mark Inversion (AMI)

• B8ZS (recommended)

DNIS, Caller ID - DTMF (Dual Tone Multi-Frequency)

Physical Termination - RJ-48X or RJ-48C

«
...
192
193
194
195
196
...
»

Summary of Contents for AltiContact Manager Version 5.0































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AltiContact Manager Version 5.0

Brand: Canon Pages: 8

3508B001 - PowerShot D10 Digital Camera

Brand: Canon Pages: 64

3508B001 - PowerShot D10 Digital Camera

Brand: Canon Pages: 47

3211B001 - PowerShot E1 Digital Camera

Brand: Canon Pages: 83

3211B001 - PowerShot E1 Digital Camera

Brand: Canon Pages: 50

eTrex H - Hiking GPS Receiver

Brand: Garmin Pages: 100

Brand: IBM Pages: 34

Brand: Allied Telesis Pages: 46

Element Manager 2.1

Brand: Cabletron Systems Pages: 108

Secure Perfect 6.1.1

Brand: GE Pages: 269

ZENWORKS APPLICATION VIRTUALIZATION - V8.0.3 INTEGRATION AND STREAMING GUIDE

Brand: Novell Pages: 36

ZENworks 10 Configuration Management

Brand: Novell Pages: 32

ZENWORKS LINUX MANAGEMENT 7.2 IR2 - 07-20-2009

Brand: Novell Pages: 134

ZENWORKS 10 CONFIGURATION MANAGEMENT SP3 - COMMAND LINE UTILITIES REFERENCE 10.3 30-03-2010

Brand: Novell Pages: 200

OPEN WORKGROUP SUITE SMALL BUSINESS EDITION 2.0

Brand: Novell Pages: 77

LINUX ENTERPRISE REAL TIME 10 SP1

Brand: Novell Pages: 7

LINUX ENTERPRISE SERVER 10 - STORAGE ADMINISTRATION GUIDE FOR EVMS

Brand: Novell Pages: 93

OPEN ENTERPRISE SERVER 2 SP 2 - CLUSTER SERVICES 1.8.7 FOR LINUX

Brand: Novell Pages: 254

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands