Altigen AltiContact Manager Version 5.0 Administration Manual Download | Manualshive

Page: 185 / 542

background image

Board Configuration

AltiContact Manager Administration Manual

6-3

6

.B
o

a

rd

Conf

igur

a

tion

Use the Board Configuration window for the Quantum board to view the
following attributes:

Parameter

Description

Board Info

Board Logical ID: assigned by AltiContact
Manager.

Board Name: the type of board installed in the
system and board ID.

Note: For Quantum boards in a Windows 2000

system:

•

the physical board ID 0 is not supported

•

the valid physical board IDs are 1–15

Channel Mapping
List

Logical Channel, Physical Span, and Physical
Channel for the entire board.

To reset the channel, select the channel to reset and
click the Reset Channel button, then click OK.

Note: Depending on whether the channel is a line or

a trunk line, double clicking a channel in this
window invokes either a Line Properties
window (see “Quantum Line Properties” on
page 13-11, or a Trunk Line Properties
window (see “Quantum Trunk Properties” on
page 7-5).

Span Info

Not available for Quantum boards.

«
...
183
184
185
186
187
...
»

Summary of Contents for AltiContact Manager Version 5.0































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AltiContact Manager Version 5.0

Brand: Garmin Pages: 12

010-10307-00 - MapSource Fishing Hot Spots

Brand: Garmin Pages: 30

Altiware HPBX 5.0A

Brand: Altigen Pages: 490

GS110TP - ProSafe Gigabit Smart Switch

Brand: NETGEAR Pages: 2

DEVICE FILTER MAC

Brand: FARONICS Pages: 30

Brand: Emagic Pages: 256

Brand: VDO Pages: 8

RSA RADIUS Server 6.1

Brand: RSA Security Pages: 118

Vox Continental

Brand: Hollow Sun Pages: 9

SmartST Professional

Brand: Navman Pages: 60

Brand: Navman Pages: 68

Brand: Symantec Pages: 105

Norton Personal Firewall 2003

Brand: Symantec Pages: 151

SERVICEDESK 7.0 MR2

Brand: Symantec Pages: 188

Brand: Unibrain Pages: 77

EDIUS Edit Station

Brand: GRASS VALLEY Pages: 4

Brand: GRASS VALLEY Pages: 2

Crown Document Option Commands

Brand: MINOLTA-QMS Pages: 134

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands