Altigen AltiContact Manager Version 5.0 Administration Manual Download | Manualshive

Page: 304 / 542

background image

Call Recording

12-8

AltiContact Manager Administration Manual

described in “Setting the Destination Folder for Centralized
Recording” on page 12-8.

3.

Select Extension Based Recording or Trunk Based Recording.

Note:

Extension Based Recording and Trunk Based Recording are
mutually exclusive. They cannot be mixed.

4.

Select the Allow Supervisor Monitor/Barge-In/Record Logout
Agent’s call check box.

Notes:

•

This feature applies to inbound and outbound workgroup calls on PCI
analog extensions to a centralized location if configured in
Workgroup Configuration.

•

Calls can be silently monitored or barged-in on, regardless of agent
login status.

Setting the Destination Folder for Centralized Recording

If you are using Windows 2003 Server and plan to use a remote shared
directory for centralized recording, follow the steps below:

WARNING!

Listening in to or recording a conversation without the consent of one or
both parties may be a violation of local, state and federal privacy laws. It
is the responsibility of the users of this feature to assure they are in
compliance with all applicable laws.

«
...
302
303
304
305
306
...
»

Summary of Contents for AltiContact Manager Version 5.0































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AltiContact Manager Version 5.0

RESIDENT CONSULTANT

Brand: Juniper Pages: 4

Brand: TC Electronic Pages: 12

Brand: Teklynx Pages: 30

Brand: Allied Telesis Pages: 46

External OEMR 2800

Brand: Dell Pages: 32

Encryption Key Manager

Brand: Dell Pages: 66

External OEMR 2950

Brand: Dell Pages: 22

Brand: Dell Pages: 10

DVS Simplified Appliance

Brand: Dell Pages: 73

Brand: Dell Pages: 75

External OEMR 850

Brand: Dell Pages: 162

External OEMR 2850

Brand: Dell Pages: 176

Brand: ESET Pages: 38

ENTERPRISE 5.4 RELEASE NOTES

Brand: Red Hat Pages: 466

DVD MOVIEFACTORY 3

Brand: Ulead Pages: 78

APPLICATION STACK 1.1 RELEASE

Brand: Red Hat Pages: 30

Data Explorer 4 Series

Brand: Applied Biosystems Pages: 447

Brand: Oracle Pages: 3232

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands