Altigen AltiContact Manager Version 5.0 Administration Manual Download | Manualshive

Page: 65 / 542

background image

Overview

AltiContact Manager Administration Manual

1-27

1

.

O

ver

view

IP Group Paging - allows the use of group voice paging to
Alti-IP 600 phone users in a group.

•

Release Link Tie - when transferring between two systems through IP
tie trunks, the trunks can be released by pressing FLASH *.

•

Ring-Back Tone Generation - ring back tones can be generated to
other analog trunk or extension lines on behalf of the IP trunk.

•

Silence Detection and Suppression - A silence detection feature
enables the following:

— Silence Suppression - when silence suppression is enabled and

silence is detected, AltiContact Manager stops sending packets to
the other side. The other side does not receive any packets and plays
silence.

— AltiContact Manager disconnects the voice mail session when a

silence period exceeds 7 seconds during voice mail recording over
VoIP.

•

VoIP Hop Off Call Support - allows an extension to access a T1 or
CO trunk on the remote system and “hop off’ to dial an outside
telephone number. This “hop off’ feature can be enabled or disabled
on the remote system. Outcall restrictions for hop off calls are
configurable.

Voice over IP Session Support AltiContact Manager
Features

The following trunk-related AltiContact Manager features are supported
during IP trunk call sessions. Refer to the AltiServ User Guide for more
details on how these features work over IP trunks.

• Incoming and Outgoing Trunk Calls

• Call Transfer To and From IP Trunk (Blind & Supervised)

• One Number Access

• Message Notification

• Reminder Calls

• Multi-Location Conferencing

• Call Park

• Call Waiting

• Call Forwarding

NEW

«
...
63
64
65
66
67
...
»

Summary of Contents for AltiContact Manager Version 5.0































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AltiContact Manager Version 5.0

Brand: Canon Pages: 8

3508B001 - PowerShot D10 Digital Camera

Brand: Canon Pages: 64

3508B001 - PowerShot D10 Digital Camera

Brand: Canon Pages: 47

3211B001 - PowerShot E1 Digital Camera

Brand: Canon Pages: 83

3211B001 - PowerShot E1 Digital Camera

Brand: Canon Pages: 50

Content Database Editor v 1.0

Brand: AMX Pages: 28

Brand: RTS Pages: 51

Brand: BrainMaster Pages: 14

Brand: Minolta Pages: 26

WISE LINUX PACKAGE EDITOR 8.0

Brand: Symantec Pages: 69

Applied Vision 4

Brand: Ken A Vision Pages: 16

Brand: Blackberry Pages: 9

ENHANCED GOOGLE MAIL PLUG IN - LEARN MORE

Brand: Blackberry Pages: 16

PRD-10459-003 - Enterprise Server For IBM Lotus Domino

Brand: Blackberry Pages: 420

Brand: Acroprint Pages: 1

TRUE IMAGE CORPORATE WORKSTATION 8.0

Brand: ACRONIS Pages: 79

TRUEIMAGE DELUXE

Brand: ACRONIS Pages: 90

Brand: ACRONIS Pages: 97

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands