manualshive.com logo in svg

Altigen AltiContact Manager Version 5.0, Administration Manual

Share
Download
Altigen AltiContact Manager Version 5.0 Administration Manual Download Page 198

Configuring the Triton T1/E1/PRI Board

6-16

AltiContact Manager Administration Manual

E1 Channel Assignment

Data Channels Assignment: 1st channel (channel ID 0)

Channels Assignment: 17th channel (channel ID 16)

Hunting: Most Idle, Least Idle, Ascend, Descend

DNIS Digits: can be 3 to 10 digits

CSU/DSU Requirements

The CSU (channel service unit) is a device used to connect a digital trunk
line coming in from the phone company to the PBX. A CSU can terminate
signals, repeat signals, and respond to loopback commands sent from the
central office.

Board Configuration

Double click the board’s icon in the Boards window (see Figure 1) to open
the Board Configuration window.

Figure 7.

Board Configuration window (Triton T1/PRI Board)

The Board Configuration window for the Triton T1/PRI board displays
the same options as the Triton Analog Station board, which is discussed in
“Configuring the Triton Analog Station Board” on page 6-4, but there are
additional options available. The Board ID must be in the range 0–7.

Summary of Contents for AltiContact Manager Version 5.0































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands