Altigen AltiContact Manager Version 5.0 Administration Manual Download | Manualshive

Page: 62 / 542

background image

Key AltiContact Manager Characteristics

1-24

AltiContact Manager Administration Manual

Scheduled Agent Auto Logout - allows an administrator to
automatically logout all workgroup agents based on up to three
(3) scheduled times.

•

Split Area Code Support - allows you to identify area codes and
prefixes that are exceptions to the standards of how area codes and
long distance prefixes are normally used. For example, this
configuration allows the system to treat calls to certain areas as local
calls.

Third Party Queue Management Application Support -
enables third party queue management applications to interact
with AltiContact Manager to replace built-in ACD queuing

functions. This allows the flexibility of offering queue customization
or extending queuing function through external applications.

Trunk Recording - recording is supported for Triton Analog,
T1/E1 and IP trunks, and can be automatically activated by
AltiContact Manager or by SDK-based applications for

incoming and/or outgoing calls.

•

Voice Mail Distribution List - allows you to create a group of
extensions for forwarding voice mail. Up to 100 distribution lists can
be created. Each distribution list can have up to 64 entries, and each
entry can be another distribution list.

•

Voice Mail Alert - An announcement can be sent to Voice Mail when
the email server disk is full.

•

Work/Hunt Group Converter - used when upgrading from AltiWare
OE 4.6, this tool that converts agents to non-agents, non-agents to
agents, workgroups to huntgroups and huntgroups to workgroups.

T1/PRI/E1 Features

T1/PRI features include:

•

ANI/DNIS Transport over T1/PRI Tie Trunks - ANI (Automatic
Number Identification) and DNIS (Dialed Number Identification
Service) digits for calls can be forwarded and transmitted between
extensions at remote AltiContact Manager systems.

•

Collecting Caller ID/DID Digits for T1 - allows you to configure the
format and sequence of caller ID and DID digits using DTMF for a T1
connection.

NEW

NEW

NEW

«
...
60
61
62
63
64
...
»

Summary of Contents for AltiContact Manager Version 5.0































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AltiContact Manager Version 5.0

Brand: Davis Instruments Pages: 108

GHOST IMAGING FOUNDATION 7.1

Brand: Symantec Pages: 189

Integrated Fiery Color Server

Brand: Xerox Pages: 24

CONTRIBUTE 3 - USING AND ADMINISTERING...

Brand: MACROMEDIA Pages: 256

Membrain Software

Brand: SanDisk Pages: 14

BJ0NJML - Service And Asset Management

Brand: IBM Pages: 330

DATA SYNCHRONIZER

Brand: Novell Pages: 50

COLDFUSION 5 - INSTALING AND CONFIGURING...

Brand: MACROMEDIA Pages: 160

ForeSight 6100 Element Management System

Brand: Patton electronics Pages: 70

Brand: British Telecom Pages: 4

Brand: VESA Pages: 18

CLUSTER SUITE FOR ENTERPRISE LINUX 4.5

Brand: Red Hat Pages: 78

Brand: M-Audio Pages: 88

pcXset - NBX - PC

Brand: 3Com Pages: 26

MEDIASTUDIO PRO 7.0 - HD PLUG-IN 2.0

Brand: Ulead Pages: 11

Brand: palmOne Pages: 114

ANTI-VIRUS 5.5 - FOR CHECK POINT FIREWALL-1

Brand: KAPERSKY Pages: 141

Brand: FARONICS Pages: 99

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands