Altigen AltiContact Manager Version 5.0 Administration Manual Download | Manualshive

Page: 161 / 542

background image

System Configuration

AltiContact Manager Administration Manual

5-11

5.
S

yst

em

Configur

a

tion

Note:

Because the business hours are used throughout the system, you or
the appropriate administrator must make sure the system time
has been set correctly. The system time can be changed using the
Date/Time utility in the Windows or NT Control Panel.

To access the Business Hour settings, select System Configuration... on
the Management menu, then click the Business Hours tab.

Figure 5.

Business Hours window, System Configuration

Multiple Business Hour profiles can be configured in a system. A default
“System” Business Hour profile is already configured. Multiple Business
Hours profiles can also be assigned to DNIS Routing and Trunk In Call
Routing entries.

«
...
159
160
161
162
163
...
»

Summary of Contents for AltiContact Manager Version 5.0































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AltiContact Manager Version 5.0

OneVision DEFINITY G3 Fault Management and integration

Brand: AT&T Pages: 153

Compliance Appliance

Brand: TANDBERG Pages: 41

Brand: Baracoda Pages: 6

Brand: Juniper Pages: 632

Brand: Black Box Pages: 65

Brand: Zing Magic Pages: 10

Brand: noveltech Pages: 13

Brand: AMX Pages: 24

Brand: GRASS VALLEY Pages: 2

Brand: Mad Catz Pages: 12

Brand: Autodesk Pages: 6

23802-091408-9020 - PSG Dwf Composer 2

Brand: Autodesk Pages: 12

Brand: Ubiquiti Pages: 38

ANTI-VIRUS 5.0 - FOR SENDMAIL WITH MILTER...

Brand: KAPERSKY Pages: 100

TIVOLI SC32-0129-00

Brand: IBM Pages: 82

Intelligent Vocal Harmony Harmony4

Brand: TC Electronic Pages: 21

Brand: DAVIS Pages: 49

Brand: Omega Engineering Pages: 63

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands