Program features
138
ST8 (error state): Drive is stopped with ramp pair 1. Relay output RO is activated. If
sequence programming is deactivated by falling edge of digital input DI1, state
machine is reset to state 1. New start command can be activated by digital input DI1
or by digital inputs DI4 and DI5 (both inputs DI4 and DI5 must be simultaneously
active).
1)
0 second ramp time = drive is accelerated/decelerated as rapidly as possible.
2)
State reference must be between 0...100%, i.e scaled AI1 value must be between
15...85%. If AI1 = 0 reference = 0% + 35% -50% = -15% < 0%.
Parameter
Setting
Additional information
EXT2 COMMANDS
SEQ PROG
Start, stop, direction commands for EXT2
EXT1/EXT2 SEL
EXT2
EXT2 activation
AI1+SEQ PROG
Addition of analog input AI1 and sequence programming output as
REF2
CONST SPEED SEL NOT SEL
Deactivation of constant speeds
RELAY OUTPUT 1
SEQ PROG
Relay output RO control as defined by parameter
/.../
8493
RUN ENABLE
NOT SEL
Deactivation of Run Enable
SEQ PROG
Digital output DO control as defined by parameter
/.../
8493
STOP FUNCTION
RAMP
Ramp stop
ACC/DEC 1/2 SEL
SEQ PROG
Ramp as defined by parameter
/.../
8492
ACCELER TIME 1
1 s
Acceleration/deceleration ramp pair 1
DECELER TIME 1
0 s
ACCELER TIME 2
20 s
Acceleration/deceleration ramp pair 2
DECELER TIME 2
20 s
RAMP SHAPE 2
5 s
Shape of the acceleration/deceleration ramp 2
SUPERV 1 PARAM
171
Sequence counter (signal
SEQ CYCLE CNTR) supervision
30
Supervision low limit
30
Supervision high limit
SEQ PROG ENABLE EXT2
Sequence programming enabled in EXT2
SEQ PROG START
DI1
Sequence programming activation through digital input (DI1)
SEQ PROG RESET
DI1(INV)
Sequence programming reset through inverted digital input DI1(INV)
DI4
Logic value 1
Operation between logic value 1 and 2
DI5
Logic value 2
CYCLE CNT LOC
ST5 TO NEXT
Sequence counter activation, i.e. sequence count increases every time
the state changes from state 5 to state 6.
CYCLE CNT RST
STATE 1
Sequence counter reset during state transition to state 1
Summary of Contents for ACS350 Series
