ABB ACS350 Series, User Manual

Page: 144 / 314

Actual signals and parameters
144
0133 PID 2 DEVIATION Deviation of the PID2 controller, i.e. the difference between the reference
value and the actual value. Unit depends on parameter
4106 UNIT and
4107 UNIT SCALE settings.
-
0134 COMM RO WORD Relay output Control Word through fieldbus (decimal). See parameter
1401 RELAY OUTPUT 1.
1 = 1
0135 COMM VALUE 1 Data received from fieldbus 1 = 1
0136 COMM VALUE 2 Data received from fieldbus 1 = 1
0137 PROCESS VAR 1 Process variable 1 defined by parameter group 34 PANEL DISPLAY -
0138 PROCESS VAR 2 Process variable 2 defined by parameter group 34 PANEL DISPLAY -
0139 PROCESS VAR 3 Process variable 3 defined by parameter group 34 PANEL DISPLAY -
0140 RUN TIME Elapsed time counter (thousands of hours). Runs when the drive is
running. Counter cannot be reset. 1 = 0.01 kh
0141 MWH COUNTER MWH counter. Counter cannot be reset. 1 = 1 MWh
0142 REVOLUTION CNTR Motor revolution counter (millions of revolutions). The counter can be
reset by pressing UP and DOWN buttons simultaneously when the
control panel is in Parameter mode. 1 = 1 Mrev
0143 DRIVE ON TIME HI Drive control board power-on time in days. Counter cannot be reset. 1 = 1 days
0144 DRIVE ON TIME LO Drive control board power-on time in 2 second ticks (30 ticks = 60
seconds). Counter cannot be reset.
0145 MOTOR TEMP Measured motor temperature. Unit depends on the sensor type selected
by group
35 MOTOR TEMP MEAS parameters.
1 = 1
0146 MECH ANGLE Calculated mechanical angle 1 = 1
0147 MECH REVS Mechanical revolutions, i.e. the motor shaft revolutions calculated by the
encoder 1 = 1
0148 Z PLS DETECTED Encoder zero pulse detector. 0 = not detected, 1 = detected. 1 = 1
0158 PID COMM VALUE 1 Data received from fieldbus for PID control (PID1 and PID2) 1 = 1
0159 PID COMM VALUE 2 Data received from fieldbus for PID control (PID1 and PID2) 1 = 1
0160 DI 1-5 STATUS Status of digital inputs. Example: 10000 = DI1 is on, DI2...DI5 are off.
0161 PULSE INPUT FREQ Value of frequency input in Hz 1 = 1 Hz
0162 RO STATUS Status of relay output. 1 = RO is energised, 0 = RO is de-energized. 1 = 1
0163 TO STATUS Status of transistor output, when transistor output is used as a digital
output. 1 = 1
0164 TO FREQUENCY Transistor output frequency, when transistor output is used as a
frequency output. 1 = 1 Hz
0165 TIMER VALUE Timer value of timed start/stop. See parameter group 19 TIMER &
COUNTER .
1 = 0.01 s
0166 COUNTER VALUE Pulse counter value of counter start/stop. See parameter group 19
TIMER & COUNTER .
1 = 1
0167 SEQ PROG STS Status Word of the sequence programming:
Bit 0 = ENABLED (1 = enabled)
Bit 1 = STARTED
Bit 2 = PAUSED
Bit 3 = LOGIC VALUE (logic operation defined by parameters
8406 … 8410 ).
1 = 1
0168 SEQ PROG STATE Active state of the sequence programming. 1...8 = state 1...8. 1 = 1
Actual signals
No. Name/Value Description FbEq