ABB ACS350 Series, User Manual

Page: 231 / 314

Actual signals and parameters
231
OR Logic function: OR 2
XOR Logic function: XOR 3
8410 SEQ LOGIC VAL 3 See parameter 8406 SEQ LOGIC VAL 1. NOT SEL
See parameter 8406 .
8411 SEQ VAL 1 HIGH Defines the high limit for the state change when parameter 8425 ST1 TRIG
TO ST 2 is set to e.g. AI1 HIGH 1.
0
0.0…100.0% Value in percent 1 = 0.1%
8412 SEQ VAL 1 LOW Defines the low limit for the state change when parameter 8425 ST1 TRIG
TO ST 2 is set to e.g. AI1 LOW 1.
0
0.0…100.0% Value in percent 1 = 0.1%
8413 SEQ VAL 2 HIGH Defines the high limit for the state change when parameter 8425 ST1 TRIG
TO ST 2 is set to e.g. AI2 HIGH 1.
0
0.0...100.0% Value in percent 1 = 0.1%
8414 SEQ VAL 2 LOW Defines the low limit for the state change when parameter 8425 ST1 TRIG
TO ST 2 is set to e.g. AI2 LOW 2.
0
0.0...100.0% Value in percent 1 = 0.1%
8415 CYCLE CNT LOC Activates the cycle counter for sequence programming.
Example: When parameter is set to ST6 TO NEXT, the cycle count (
0171
SEQ CYCLE CNTR) increases every time the state changes from state 6 to
state 7.
NOT SEL
NOT SEL Disabled 0
ST1 TO NEXT From state 1 to state 2 1
ST2 TO NEXT From state 2 to state 3 2
ST3 TO NEXT From state 3 to state 4 3
ST4 TO NEXT From state 4 to state 5 4
ST5 TO NEXT From state 5 to state 6 5
ST6 TO NEXT From state 6 to state 7 6
ST7 TO NEXT From state 7 to state 8 7
ST8 TO NEXT From state 8 to state 1 8
ST1 TO N From state 1 to state n. State n is defined by parameter 8427 ST1 STATE N. 9
ST2 TO N From state 2 to state n. State n is defined by parameter 8427 ST1 STATE N. 10
ST3 TO N From state 3 to state n. State n is defined by parameter 8427 ST1 STATE N. 11
ST4 TO N From state 4 to state n. State n is defined by parameter 8427 ST1 STATE N. 12
ST5 TO N From state 5 to state n. State n is defined by parameter 8427 ST1 STATE N. 13
ST6 TO N From state 6 to state n. State n is defined by parameter 8427 ST1 STATE N. 14
ST7 TO N From state 7 to state n. State n is defined by parameter 8427 ST1 STATE N. 15
ST8 TO N From state 8 to state n. State n is defined by parameter 8427 ST1 STATE N. 16
8416 CYCLE CNT RST Selects the source for the cycle counter reset signal ( 0171 SEQ CYCLE
CNTR).
NOT SEL
DI5(INV) Reset through inverted digital input DI1(INV). 0 = active, 1 = inactive. -5
DI4(INV) See selection DI1(INV). -4
DI3(INV) See selection DI1(INV). -3
DI2(INV) See selection DI1(INV). -2
Parameters – complete descriptions
Index Name/Selection Description Def, FbEq