manualshive.com logo in svg

Siemens Synco700 RMK770, Руководство по документации


Поделиться
Скачать
background image

58/226 

Building Technologies 

Boiler Sequence Controller RMK770 

CE1P3132en 

HVAC Products 

5 General functions, fundamentals 

01.03.2005 

5 

General functions, fundamentals 

5.1 Time 

switch 

 

A time switch is available for the heating circuit. In “Automatic”  mode, the heating cir-
cuit, operates according to that time switch. A switching program can be defined for 
each day of week. 
Using the program entered, the time switch controls the change of operating modes 
and the associated setpoints. 
Operation of the time switch is described in Operating Instructions B3131. 

5.1.1 Communication 

 

If the controller is connected to other controllers via communication, the time switch can 
be provided to other controllers, or the time switch of some other controller can be 
used.  

Following combinations are possible:  

Entry Effect 

Diagram 

Autono-
mous 

Time switch only acts locally on this controller. 
It has no impact on other controllers on the 
bus. 

 

Slave 

The time switch in this controller is not active. 
The time switch acting is the external time 
switch acting in the geographical zone set on 
this controller as the time switch receiving 
zone. The external time switch must be set as 
the time switch master. 

 

Master 

The time switch in this controller is active. 
The time switch also acts on all other control-
lers where the time switch is switched off (time 
switch slave) and which have the geographical 
zone of this controller set as the time switch 
receiving zone. 

31

4

0Z

0

8

 

 

  Main menu > Commissioning > Communication > Room Heating circuit

 

Operating line 

Range 

Factory setting 

Geographical zone (apartment) 

1…126 1 

Time switch operation 

Autonomous / Slave / 
Master 

Autonomous 

Time switch slave (apartment) 

1…126 1 

5.1.2 

Time switch for external controllers on the bus 

 

The time switch can also be provided to external controllers on the bus.  
If the RMK770 is not connected to a heating circuit, the time switch will automatically be 
hidden. But if required, this time switch can be used for external controllers on the bus 
(e.g. for RXB… room controllers).  
For that purpose, the hidden time switch must be activated.  
 

Содержание Synco700 RMK770



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Synco700 RMK770

KAR-TECH MICRO Installation And Operation Manual preview
MICRO
Бренд: KAR-TECH Страницы: 28
2M Technology 2MTHFR-2M Quick Manual preview
2MTHFR-2M
Бренд: 2M Technology Страницы: 17
2iB SC10 Quick Start Manual preview
SC10
Бренд: 2iB Страницы: 5
2gig Technologies Go!Control Panel Installation & Programming Manual preview
Go!Control Panel
Бренд: 2gig Technologies Страницы: 78
Fanimation BTCR9 Quick Start Manual preview
BTCR9
Бренд: Fanimation Страницы: 2
M2M C600 Technical Manual preview
C600
Бренд: M2M Страницы: 24
RBI FUTERA XLF Series Control Manual preview
FUTERA XLF Series
Бренд: RBI Страницы: 128
RBH Access Technologies UNC100 Hardware Manual preview
UNC100
Бренд: RBH Access Technologies Страницы: 36
S&C PMH Inspection Manual preview
PMH
Бренд: S&C Страницы: 11
S&C BankGuard PLUS Installation Manual preview
BankGuard PLUS
Бренд: S&C Страницы: 24
S&C BankGuard PLUS Operation preview
BankGuard PLUS
Бренд: S&C Страницы: 19
Bardiani BBZK Manual preview
BBZK
Бренд: Bardiani Страницы: 96
Eaton CDAU-01/04 Instruction Leaflet preview
CDAU-01/04
Бренд: Eaton Страницы: 4
Valence Tech iBT-07 Manual preview
iBT-07
Бренд: Valence Tech Страницы: 12
Dungs 273061 Instructions Manual preview
273061
Бренд: Dungs Страницы: 56
Emec PH CONTROLLER Operating Manual preview
PH CONTROLLER
Бренд: Emec Страницы: 8
Velleman WS8426 User Manual preview
WS8426
Бренд: Velleman Страницы: 34
Conbraco Industries Apollo 70-600 Series Installation, Operation And Maintenance Manual preview
Apollo 70-600 Series
Бренд: Conbraco Industries Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды