Siemens Synco700 RMK770 Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 226

background image

53/226

Building Technologies

Boiler Sequence Controller RMK770

CE1P3132en

HVAC Products

4 General settings

01.03.2005

4 General

settings

4.1

Time of day and date

4.1.1 Operating

principle

The controller has a yearly clock with time of day, weekday and date.

The following time formats are available:

Time format

Date

Example

Time of day

Example

24 hours

dd.mm.yyyy
(day.month.year)

31.05.2004 hh:mm

(hours:

minutes)

15:56

am/pm mm/dd/yy

(day/month/year)

05/31/2004 hh:mm am/pm

(hours

:

minutes am/pm)

03:56 PM

Main menu > Commissioning > Settings > …

or

Main menu > Settings > Device

Operating line

Range

Factory setting

Time format

24 hours / 12 hours
(am/pm)

24 hours

Main menu > Time of day / Date

Operating line

Range

Factory setting

Time of day

00:00…23:59 00:00

Date 01.01…31.12

01.01

Year 2000…2100

2000

The change from summertime to wintertime, and vice versa, is made automatically. The
date of the earliest changeover can be adjusted should the relevant regulations change.
The dates set for the change from wintertime to summertime, or from summertime to
wintertime, ensure that on the first Sunday after that date the time of day will change
from 02:00 (wintertime) to 03:00 (summertime), and from 03:00 (summertime) to 02:00
(wintertime).
If both dates are set to coincide, summer-/wintertime changeover will be inactive.

Main menu > Time of day / Date

Operating line

Range

Factory setting

Summertime start

01.01. … 31.12

25.03

Wintertime start

01.01. … 31.12

25.10

4.1.2 Communication

For the time of day, there are several sources available, depending on the master
clock. This can be entered on the controller. Time of day and date can be exchanged
via bus.
The following settings for clock time operation are possible:

•

Autonomous (does not send and does not receive)

•

Time of day

via

bus: Clock time slave (receives the synchronization signal via bus)

•

Time of day

on

the bus: Clock time master (sends the synchronization signal to the

bus)

Commissioning > Communication > Basic settings >

Time format

Setting

Summer-/wintertime
changeover

Setting

Setting

«
...
51
52
53
54
55
...
»

Содержание Synco700 RMK770



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Synco700 RMK770

Бренд: NCR Страницы: 6

Бренд: Particle Страницы: 6

Бренд: National Instruments Страницы: 29

xPico 200 Series

Бренд: Lantronix Страницы: 7

Бренд: Lantronix Страницы: 3

Бренд: Lantronix Страницы: 15

Бренд: OBSIDIAN CONTROL SYSTEMS Страницы: 13

Бренд: olympia electronics Страницы: 10

Бренд: Balboa Страницы: 74

Бренд: Cadac Страницы: 4

Бренд: L-Acoustics Страницы: 24

Бренд: L-Acoustics Страницы: 21

Бренд: M&S Systems Страницы: 4

Бренд: Xilinx Страницы: 52

Бренд: ZKTeco Страницы: 11

PowerFlex 755 IP00

Бренд: Allen-Bradley Страницы: 78

Бренд: MULTISPAN Страницы: 2

HmIP-FAL230-C10

Бренд: HomeMatic Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды