manualshive.com logo in svg

Siemens Synco700 RMK770, Руководство по документации


Поделиться
Скачать
background image

194/226 

Building Technologies 

Boiler Sequence Controller RMK770 

CE1P3132en 

HVAC Products 

14 Fault tracing support 

01.03.2005 

14  Fault tracing support 

 

If a fault is displayed, it is always practical to select operating line 

Faults > Faults current

 

and look for any pending fault status messages before starting to rectify faults. If an 
extension module is faulty, that fault must always be rectified first because it may lead 
to a number of subsequential fault status messages. 

 

14.1  Error code list 

 

The RMK770 has maximum 1 heating circuit and 1 time switch. Index 1 indicates that 
the sensor error occurred on this plant. 

 

Number 

Name 

Possible cause, remarks 

10 

Outside temp sensor 
error 

Outside temperature sensor not connected, bus 
communication interrupted.  
Outside temperature zone not correctly set 
(transmitter and receiver must have the same 
outside temperature zone).  
Backup value is 0 °C. 
Nonurgent message; must not be acknowledged 

11 

>1 outside tempera-
ture sensor 

More than 2 outside temperature sensors in the 
same outside temperature zone.  
Urgent message; must be acknowledged 

12 

Outs sensor simula-
tion active 

Simulation of the outside temperature is still ac-
tive. Simulation of the outside temperature may 
only temporarily stay active.  
Nonurgent message; must not be acknowledged 

50 

[HC 1] flow sensor 
error 

Nonurgent message; must be acknowledged 

51 

[HC 1] return sensor 
error 

Error return temperature sensor heating circuit 1. 
Nonurgent message; must be acknowledged 

57 

Prim controller error 
flow sensor 

Error primary controller flow temperature sensor.  
Nonurgent message; must be acknowledged 

58 

Prim controller error 
ret sensor 

Error primary controller return temperature sen-
sor.  
Nonurgent message; must be acknowledged 

60 

Room sensor error 
plant 1 

Error room temperature sensor plant 1. 
Nonurgent message; must not be acknowledged 

61 

>2 room sensors in 
plant 1 

More than 2 room temperature sensor for plant 1 
in the same geographical zone.  
Urgent message; must be acknowledged 

301 

[Boiler 1] boiler 
sensor error 

Error boiler sensor boiler 1 

302 

[Boiler 2] boiler 
sensor error 

Error boiler sensor boiler 2 

303 

[Boiler 3] boiler 
sensor error 

Error boiler sensor boiler 3 

304 

[Boiler 4] boiler 
sensor error 

Error boiler sensor boiler 4 

305 

[Boiler 5] boiler 
sensor error 

Error boiler sensor boiler 5 

Содержание Synco700 RMK770



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Synco700 RMK770

ABB Relion REC670 Product Manual preview
Relion REC670
Бренд: ABB Страницы: 138
ABB Relion REC670 Operator'S Manual preview
Relion REC670
Бренд: ABB Страницы: 116
ABB Relion 615 series Operation Manual preview
Relion 615 series
Бренд: ABB Страницы: 136
ABB 615 Series ANSI Manual preview
615 Series ANSI
Бренд: ABB Страницы: 60
Samson 3510 Mounting And Operating Instructions preview
3510
Бренд: Samson Страницы: 48
Mako Networks 6000 Series Quick Installation Manual preview
6000 Series
Бренд: Mako Networks Страницы: 15
H3C WX Series Configuration Manual preview
WX Series
Бренд: H3C Страницы: 69
Samson 3277 Quick Manual preview
3277
Бренд: Samson Страницы: 2
Paradox Digiplex DGP-848 Reference And Installation Manual preview
Digiplex DGP-848
Бренд: Paradox Страницы: 20
Vageo DT-1 Plus Manual preview
DT-1 Plus
Бренд: Vageo Страницы: 2
Vacon 100 INDUSTRIAL Additional Installation Instruction preview
100 INDUSTRIAL
Бренд: Vacon Страницы: 6
Vacon 100 INDUSTRIAL Technical Manual preview
100 INDUSTRIAL
Бренд: Vacon Страницы: 24
Vacon 100X series Marine Installation Manual preview
100X series
Бренд: Vacon Страницы: 30
Vacon 100 flow User Manual preview
100 flow
Бренд: Vacon Страницы: 81
Vacon 100X series Installation And Maintenance Manual preview
100X series
Бренд: Vacon Страницы: 100
Zamel Extra Free RZB-02 Quick Manual preview
Extra Free RZB-02
Бренд: Zamel Страницы: 2
Yamaha DCP4S-US Owner'S Manual preview
DCP4S-US
Бренд: Yamaha Страницы: 2
D&R ELECTRONICS RDS17S-ELITE1-R1 Installation Manual preview
RDS17S-ELITE1-R1
Бренд: D&R ELECTRONICS Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды