manualshive.com logo in svg

Siemens Synco700 RMK770, Руководство по документации, Страница: 62 / 226

Поделиться
Скачать
Siemens Synco700 RMK770 Скачать руководство пользователя страница 62

62/226 

Building Technologies 

Boiler Sequence Controller RMK770 

CE1P3132en 

HVAC Products 

5 General functions, fundamentals 

01.03.2005 

(slaves). 

T

he time of the special day is a preselection made by the master and applies 

to all controllers in the same holidays/special days zone.  

5.2.4 Calendar 

entry 

 

A maximum of 16 entries can be made. The entries are sorted in chronological order. 
Every entry must include: 

•

  Date, year and starting time  

•

  Date and end time 

•

  Reason for entry (holidays or special day) 

 

  Main menu > Holidays/special days > Calendar 

Operating line 

Range 

Factory setting 

Entry 1… entry 16 

Start / End / Reason 

--- / --- / Holidays 

Annually recurring holidays or special days can be entered by setting an asterisk (*) for 
the annual setting. 
 
If 2 entries overlap, following applies: Special days have priority over holidays. Hence, it 
is also possible to have a special day during a holiday period.  
 
An example of a special day during the holiday period would be a theatre performance 
in a school building. 
 
At the end of the holiday period or special day, operation according to the normal 7-day 
program will be resumed. During this transition period, it can occur that optimum start 
control (e.g. boost heating) cannot be started in due time. It is therefore recommended 
to bring the end of the holiday period somewhat forward, thereby giving the plant suffi-
cient time to adapt to the respective setpoints. 

5.2.5 

Control inputs for holidays and special days 

    

Holidays and special days can also be activated via digital inputs. For that purpose, 
digital inputs must be assigned.  
 

  Main menu > Commissioning > Extra configuration > Miscellaneous > Inputs 

 

Operating line 

Range 

Factory setting 

Holiday input 

RMK770…, RMZ7…* 

--- 

Special day input 

RMK770…, RMZ7…* 

--- 

*  Here, the free inputs are available for selection 

These inputs are only active if holidays/special day operation is set to “Autonomous“ or 
“Master”.  
 
The digital input enables the plant to constantly use the special day program set in the 
7-day program without necessitating interventions on the controller. 
When the configured input is activated, the special day program will become active. 
This program is maintained until the input becomes inactive. Then, the normal 7-day 
program will be resumed. 
 
The digital input enables the plant to be constantly switched to ”Holidays” mode without 
necessitating interventions on the controller. 
When the configured input is activated, the plant switches to the “Holidays” mode. This 
program is maintained until the input becomes inactive. Then, the normal 7-day pro-
gram will be resumed. 
 

Setting 

Priority 

Example 

Note 

Setting 

Special day 

Holidays 

Содержание Synco700 RMK770



































































































































































































































Отзывы:

Нет отзывов