manualshive.com logo in svg

Siemens Synco700 RMK770, Руководство по документации, Страница: 124 / 226

Поделиться
Скачать
Siemens Synco700 RMK770 Скачать руководство пользователя страница 124

124/226 

Building Technologies 

Boiler Sequence Controller RMK770 

CE1P3132en 

HVAC Products 

7 Boiler temperature control 

01.03.2005 

Number Text 

Effect 

301 

[Boiler 1] boiler sensor 
error 

Urgent message; must be acknowledged. 
Aggregate stop boiler 1  

302 

[Boiler 2] boiler sensor 
error 

Urgent message; must be acknowledged. 
Aggregate stop boiler 2  

303 

[Boiler 3] boiler sensor 
error 

Urgent message; must be acknowledged. 
Aggregate stop boiler 3 

304 

[Boiler 4] boiler sensor 
error 

Urgent message; must be acknowledged. 
Aggregate stop boiler 4  

305 

[Boiler 5] boiler sensor 
error 

Urgent message; must be acknowledged. 
Aggregate stop boiler 5  

306 

[Boiler 6] boiler sensor 
error 

Urgent message; must be acknowledged. 
Aggregate stop boiler 6  

 

If the boiler temperature sensor is faulty, the burner will be shut down.  
 

Number Text 

Effect 

311 

[Boiler 1] return sensor 
error 

Nonurgent message; must be acknowl-
edged. No aggregate stop boiler 1 

312 

[Boiler 2] return sensor 
error 

Nonurgent message; must be acknowl-
edged. No aggregate stop boiler 2 

313 

[Boiler 3] return sensor 
error 

Nonurgent message; must be acknowl-
edged. No aggregate stop boiler 3 

314 

[Boiler 4] return sensor 
error 

Nonurgent message; must be acknowl-
edged.

 

No aggregate stop boiler 4 

315 

[Boiler 5] return sensor 
error 

Nonurgent message; must be acknowl-
edged.

 

No aggregate stop boiler 5 

316 

[Boiler 6] return sensor 
error 

Nonurgent message; must be acknowl-
edged. No aggregate stop boiler 6 

 

In the case of plant with mixing valve for the maintained boiler return temperature, the 
mixing valve will be driven to the fully closed position when there is no return tempera-
ture sensor and then deenergized to make possible manual adjustment. 

Otherwise, the control behaves like a plant without return temperature sensor. 
 

Number Text 

Effect 

321 

[K1] flue gas temp sensor 
error 

Nonurgent message; must be acknowl-
edged. No aggregate stop boiler 1 

322 

[K2] flue gas temp sensor 
error 

Nonurgent message; must be acknowl-
edged. No aggregate stop boiler 2 

323 

[K3] Flue gas temp sen-
sor error 

Nonurgent message; must be acknowl-
edged. No aggregate stop boiler 3 

324 

[K4] flue gas temp sensor 
error 

Nonurgent message; must be acknowl-
edged. No aggregate stop boiler 4 

325 
 

[K5] flue gas temp sensor 
error 

Nonurgent message; must be acknowl-
edged. No aggregate stop boiler 5 

326 

[K6] flue gas temp sensor 
error 

Nonurgent message; must be acknowl-
edged. No aggregate stop boiler 6 

 

Number Text 

Effect 

2301 

[K1 burner] fault 

Urgent message; must be acknowledged. 
Aggregate stop boiler 1  

2302 

[K2 burner] fault 

Urgent message; must be acknowledged. 
Aggregate stop boiler 2  

Error boiler tempera-
ture sensor  
 

Error return tempera-
ture sensor 

Error flue gas 
temperature sensor 

Fault burner 
 

Содержание Synco700 RMK770



































































































































































































































Отзывы:

Нет отзывов