manualshive.com logo in svg

Siemens Synco700 RMK770, Руководство по документации


Поделиться
Скачать
background image

143/226 

Building Technologies 

Boiler Sequence Controller RMK770 

CE1P3132en 

HVAC Products 

9 Precontrol 

01.03.2005 

Setting “System pump locking signal = Off“ means that the system pump shall also 
respond to locking signals. 
 

  Main menu > Settings > Primary controller > Limitations

 

Operating line 

Range 

Factory setting 

Flow temperature max  

0…140 °C 

140 °C 

Flow temperature min  

---- / 0…140 °C 

---- °C 

Flow temperature rise max 

---- / 1…600 K/h 

---- K/h 

Return temp min* 

---- / 0…140 °C 

---- °C 

Return temp max* 

---- / 0…140 °C 

---- °C 

Frost protection for the plant  

Off / On 

On 

* Displayed or hidden, depending on the type of limitation  

9.8.3 

Pump overrun and mixing valve overrun 

  

To protect the boiler against overtemperatures after the burner has shut down (when 
there are no more active heat consumers), an overrun time for the consumers can be 
set on the boiler controller. 
After the burner has shut down, the overrun time ensures that the heating circuits and 
DHW heating will still draw heat for that period of time provided they were consuming 
heat up to 1 minute before the burner was shut down. In any case, pumps and mixing 
valves have an overrun time of 60 seconds.  
With primary controller type 1, the mixing valve maintains the former setpoint during the 
overrun time and the pump runs; with primary controller type 2, only the pump runs during 
that period of time. 

9.8.4 

Pump kick and valve kick 

  

The pump kick is a protective function that is carried out periodically. It prevents pumps 
and / or mixing valves from seizing after longer off periods.  
For more detailed information, refer to section 5.5 “Pump kick and valve kick”. 

9.9 Error 

handling 

 

When commissioning is completed (commissioning menu quit), the system checks 
whether the configured sensors have been connected. In the event of an open-circuit or 
short-circuit, an error message will be delivered. 
 

Number Text 

Effect 

57 

Prim controller error flow 
sensor 

Nonurgent message; must be acknowl-
edged 

In the case of an error of the flow temperature sensor, the mixing valve will be driven to 
the fully closed position to become inactive (3-position actuator), so that it can be 
manually operated. 
 

Number Text 

Effect 

58 

Prim controller error ret 
sensor 

Nonurgent message; must be acknowledged 

The primary controller behaves as if no return temperature sensor was used. Limitation 
of the return temperature is inactive. 
 

System pump and 
locking signals 

Settings 

Error handling 

Errors of sensors 

Sensor error return 
temperature 

Содержание Synco700 RMK770



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Synco700 RMK770

ABB Relion REC670 Product Manual preview
Relion REC670
Бренд: ABB Страницы: 138
ABB Relion REC670 Operator'S Manual preview
Relion REC670
Бренд: ABB Страницы: 116
ABB Relion 615 series Operation Manual preview
Relion 615 series
Бренд: ABB Страницы: 136
GBD BA100 Instructions For Installations preview
BA100
Бренд: GBD Страницы: 68
Idesco EPC Manual preview
EPC
Бренд: Idesco Страницы: 11
B meters IWM-LR4 Quick User Manual preview
IWM-LR4
Бренд: B meters Страницы: 2
Parker A4W Series Installation And Service Information preview
A4W Series
Бренд: Parker Страницы: 12
Parker AC890PX Series User Mounting And Assembly Instructions preview
AC890PX Series
Бренд: Parker Страницы: 30
Parker Compax3M Series Installation Manual preview
Compax3M Series
Бренд: Parker Страницы: 52
Parker AC30V Series Manual preview
AC30V Series
Бренд: Parker Страницы: 337
u-blox M8 Series Hardware Integration Manual preview
M8 Series
Бренд: u-blox Страницы: 28
u-blox EVK-NINA-W151 Quick Start preview
EVK-NINA-W151
Бренд: u-blox Страницы: 2
Klimaire KUMR-903 Operation Manual preview
KUMR-903
Бренд: Klimaire Страницы: 5
Audioaccess PX-700 Manual preview
PX-700
Бренд: Audioaccess Страницы: 2
Game ready Equine 550250 User Manual preview
Equine 550250
Бренд: Game ready Страницы: 24
Climatisation RC4 Operating Manual preview
RC4
Бренд: Climatisation Страницы: 52
TECOM Challenger v8 Quick Reference User Manual preview
Challenger v8
Бренд: TECOM Страницы: 8
Finnleo SaunaLogic SL2 Control Manual preview
SaunaLogic SL2 Control
Бренд: Finnleo Страницы: 14

Бренды по названию

Популярные бренды

Загрузить еще бренды