Siemens Synco700 RMK770 Скачать руководство пользователя страница 94 | Manualshive

Страница: 94 / 226

Siemens Synco700 RMK770 Скачать руководство пользователя страница 94

94/226

Building Technologies

Boiler Sequence Controller RMK770

CE1P3132en

HVAC Products

6 Boiler sequence management

01.03.2005

The main pump, like the boiler pump, never responds to locking signals.
Whether or not the system pump shall respond to locking signals can be selected on
function block “Primary controller”.

Main menu > Commissioning > Settings > …

or

Main menu > Settings >

Primary controller > Limitations

Operating line

Range

Factory setting

System pump locking signal

On / Off

Off

6.6.2

Maximum limitation of the flow temperature setpoint

Main menu > Commissioning > Settings > …

or

Main menu > Settings >

Boiler sequence manager > Limitations

Operating line

Range

Factory setting

Main flow setpoint max

25…140 °C

95 °C

Using this setting, the flow temperature setpoint, which is calculated by the function
block through generation of the maximum value, can be limited at a maximum.

6.6.3 Frost

protection

For more detailed information, refer to subsection 7.9.9 “Frost protection for the boiler”.

Main menu > Commissioning > Settings > …

or

Main menu > Settings >

Boiler sequence manager > Limitations

Operating line

Range

Factory setting

Frost protection for the plant

On / Off

Off

Here, it can be selected whether frost protection for the plant shall act on the main
pump. For more detailed information about frost protection for the plant, refer to section
5.3 “Frost protection for the plant”.

If the temperature at the main flow temperature sensor TMnFl falls below 5 °C, a heat
requisition of 10 °C will be generated. If the temperature at the sensor returns to a level
above 7 °C, the function will be deactivated. The function is active for a minimum of
5 minutes.

If the temperature at the consumer return temperature sensor TRtCo falls below 5 °C, a
heat requisition of 10 °C will be generated. If the temperature at the sensor returns to a
level above 7 °C, the function will be deactivated. The function is active for a minimum
of 5 minutes.

6.7 Diagnostics

The first diagnostic choice is offered by the info pages “Boiler sequence”, “Boiler se-
quence manager”, “Temperatures” and “Boilers”.
Info page “Boiler sequence“ shows:

•

The number of boilers included in the boiler sequence

•

The current lead boiler

•

The number of boilers released (release

9

)

•

Whether the burner operates (Off, first stage, second stage, modulating)

•

Whether the boiler is faulty

Frost protection for the
boiler

Frost protection for the
plant

Frost protection for the
main flow temperature

Frost protection for the
consumer return
temperature

«
...
92
93
94
95
96
...
»

Содержание Synco700 RMK770



































































































































































































































Отзывы:

Нет отзывов