Siemens Synco700 RMK770 Скачать руководство пользователя страница 92 | Manualshive

Страница: 92 / 226

Siemens Synco700 RMK770 Скачать руководство пользователя страница 92

92/226

Building Technologies

Boiler Sequence Controller RMK770

CE1P3132en

HVAC Products

6 Boiler sequence management

01.03.2005

Heat demand can be predefined with a DC 0…10 V signal.
The signal can be matched to the DC 0…10 V signal source:

Main menu > Commissioning > Settings > …

or

Main menu > Settings > Inputs > Heat requisition boiler sequence

Operating line

Range

Factory setting

[Modulating] setpoint at 0 V

–150…50 °C

0 °C

[Modulating] setpoint at 10 V

50…500 °C

100 °C

[Modulating] limit value

0…140 °C

10 °C

DC 0...10 V

0

2

4

6

8

10

-20

0

20

40

60

80

100

120

°C

2

3

313

1D14

c

Value in °C at DC 0 V

d

Value in °C at DC 10 V

e

Limit value for heat demand (temperatures below this level are interpreted as “no heat demand”)

With the binary input, heat demand can be predefined in the form of a fixed value.
The “Inputs“ menu can be used to parameterize whether the input shall be activated
with a closed or open contact.

Main menu > Commissioning > Settings > …

or

Main menu > Settings > Inputs > RMK770…

or

RMZ78…

Operating line

Range

Factory setting

Normal position

Open / Closed

Open

Setting “Normal position = Open” means that a closed contact identifies a heat requisi-
tion.

Main menu > Commissioning > Settings > …

or

Main menu > Settings > Inputs > Heat requisition Heat requisition boiler sequence

Operating line

Range

Factory setting

[2-pos] setpoint normal

0…140 °C

70 °C

With the binary input, it is also possible to predefine a fixed value as a heat demand,
which maximum value generation interprets like a heat requisition of the DHW or frost
type.
Depending on the boiler sequence operating mode (see above), only 1 requisition of
the DHW type and / or frost type is considered.

Main menu > Commissioning > Settings > …

or

Main menu > Main menu > Settings > Inputs > Heat requisition boiler sequence

Operating line

Range Factory

setting

[2-pos] setpoint DHW

0…140 °C

70 °C

[2-pos] setpoint frost prot

0…140 °C

70 °C

Heat requisition
modulating

Heat requisition 2-
position

Heat requisition 2-
position [DHW or frost
protection]

«
...
90
91
92
93
94
...
»

Содержание Synco700 RMK770



































































































































































































































Отзывы:

Нет отзывов